Quick Answer: What Is a Pole Barn Carport, and What Does One Cost?
A pole barn carport is a metal post-frame roof carried on a few widely spaced columns, with the sides left open and the floor between them clear. The columns are set in the ground or on engineered brackets, so a two-vehicle footprint has nothing in the middle of it. At 24×36, or 864 square feet, a kit is $7,800–$27,600. Installed, with the slab, the erection, the site work and the permit, it is $19,100–$57,100, or $22 to $66 per square foot.
Simplify your research by letting us do the work for you.

Pole Barn Carport Spans and Costs: an Open Metal Roof on Widely Spaced Posts
A pole barn carport is a roof carried on a few widely spaced columns, with the sides left open. That is the whole idea, and it separates it from the light bolted shelter that arrives flat-packed on a pallet: fewer columns, set in the ground or on engineered brackets, and a clear floor between them. You park under it, you back a trailer through it, and nothing in the middle is in the way.
This page is the general open structure, for cars, trucks, trailers and equipment. A roof sized for a motorhome is an RV Carport, and the light bolted kit sold by width and length is a Metal Carport. The timber-framed answer is a Wood Carport, an odd footprint or a roof line matched to the house is what Custom Carports covers, and once walls and doors go on it becomes a Pole Barn Garage. What follows is spans, posts, footings, slope, enclosure and price.
What Post-Frame Does That a Bolted Shelter Cannot

The difference is structural, not cosmetic. A light shelter kit carries its roof on many small legs at close centres, because each leg can take only so much. A pole barn carport carries the same roof on a handful of engineered columns, so the bays are wide and the middle of the floor is empty. That is the reason to buy one: you are paying for the clear space, not the steel.
The trade body for these buildings puts the capability plainly. Metal building systems "can span great widths and lengths with or without additional interior supports", the Metal Building Manufacturers Association says. They are designed for the job in front of them: "Metal buildings are governed by the same building codes and material standards as other forms of construction." An engineered building is not a heavier version of a catalogue one.
The foundation follows from the frame. A pole barn carport carries load through embedded or bracketed columns rather than a continuous perimeter footing. That normally means less concrete and less excavation than a comparable rigid-frame building, with embedment and uplift resistance engineered for the site's soil and loads.
Bay Spacing, Clear Width and the Number on the Quote

Bay spacing is the distance between columns down the length of a pole barn carport, and it is the number that decides what you can drive between. Wider bays mean deeper headers and bigger columns; closer bays mean lighter members and more obstacles on the ground. Which you get depends on the loads, the span and what the engineer signs.
No honest figure can be printed here for that spacing: it is a sealed-drawing decision, not a catalogue one. What you can do is ask every supplier the same question in feet and inches — the clear distance between columns, and the clear height under the lowest member, whether that is a header, a brace or a light.
It matters because a building sold as twenty-four feet wide is measured outside to outside, so the opening you can use is less. Width mid-bay is not width at a column, and a pole barn carport that just fits a truck and trailer on paper can fail at the column line on delivery day.
Ask for clear dimensions in writing
Nominal size, clear span between columns and clear height are three different numbers, and only the last two decide whether the vehicle fits. Get them on the quote, not in a phone call, and check them against the drawing.
Length is easier: bay spacing multiplied by the number of bays, so a longer building is repetition rather than redesign. Adding a bay now is the cheapest space you will ever buy on a pole barn carport, and far cheaper than an extension later.
Posts in the Ground: Embedment, Footings and Frost

A pole barn carport asks its columns to do two jobs: carry the roof down, and stop it being lifted and pushed sideways. The building code has a section for exactly this condition, covering "Designs to resist both axial and lateral loads employing posts or poles as columns embedded in earth or in concrete footings in earth". It says "The depth to resist lateral loads shall be determined using the design criteria" set out there. Embedment is calculated from the soil and the force at the top of the column, not picked from round numbers.
Frost is the other half. The code requires that "foundations and other permanent supports of buildings and structures shall be protected from frost", by "Extending below the frost line of the locality" or by an engineered alternative. Frost depth is local, and the building department is the only source for the figure it enforces.
The small-building exception rarely covers a pole barn carport
Free-standing structures escape frost protection only where every condition holds. The lowest risk category. An "Area of 600 square feet (56 m2) or less for light-frame construction or 400 square feet (37 m2) or less for other than light-frame construction". And an "Eave height of 10 feet (3048 mm) or less". A roof for two vehicles fails the area test; one tall enough to back a trailer under fails the height test too.
Three things belong on the drawings before anyone digs: embedment depth or footing size at each column, the uplift connection at the top of the column, and the connection from roof member to header. Those are the three places a roof on posts comes apart, in that order.
Price an Open Structure for Your Own Site
Frost depth, wind speed and snow load are local, and so is the price. One form puts your footprint and county in front of suppliers who build open metal post-frame buildings.
Get Free QuotesNo obligation. Up to 5 suppliers.
Open Sides, Partial Enclosure and What the Code Calls Each

How open the sides are is not a style question. It puts a pole barn carport in a class, and the class changes the wind design. The code defines an open building as "A building having each wall at least 80 percent open". A partially enclosed building is one where "The total area of openings in a wall that receives positive external pressure exceeds the sum of the areas of openings in the balance of the building envelope" by a set margin. An enclosed building is "A building that does not comply with the requirements for open or partially enclosed buildings".
So sheeting one end changes more than the look of it: the same roof moves into a different class and a different set of pressures. Decide how much you want closed in before the drawings are sealed.
The wind requirement itself is unambiguous. The code requires that "Wind loads on every building or structure shall be determined in accordance with Chapters 26 to 31 of ASCE 7". Members "shall be anchored to resist wind-induced overturning, uplift and sliding and to provide continuous load paths for these forces to the foundation". Separately: "Anchorage of the roof to walls and columns, and of walls and columns to foundations, shall be provided to resist the uplift and sliding forces". With no walls to lean on, a pole barn carport puts all of that through its columns and footings.
Snow is the load people assume is unchanged, and it is not. The code's thermal factor table sets the factor at 1.0 for "All structures except as indicated below" and at 1.2 for "Unheated structures". A pole barn carport is unheated by definition, so its design snow load is a fifth higher than a heated building of the same shape on the same lot. Nothing underneath makes heat, so the snow sits instead of sliding.
Ground snow is not roof snow
The county ground snow load is a starting figure, not the design load: it is converted using factors for exposure, thermal condition and slope, so quoting the ground number as the roof number understates it. There is no national design value for wind or snow. The ASCE Hazard Tool returns both for an exact address — ask which figures the drawings assume.
Roof Pitch, Panel Slope and Where the Water Lands

Pitch is where an open roof differs most from a closed one, because nothing catches what comes off it. The code sets a floor by panel type. Its deck slope section states that "The minimum slope for lapped, nonsoldered seam metal roof panels without applied lap sealant shall be three units vertical in 12 units horizontal".
With sealant applied, the same panels may go to "one-half unit vertical in 12 units horizontal". And "The minimum slope for standing-seam metal roof panel systems shall be one-quarter unit vertical in 12 units horizontal". Which panel is on the quote decides how flat the roof may be.
Above that floor, pitch is a weather decision. Steeper sheds rain and snow sooner; shallower keeps a pole barn carport lower, which matters where a height limit applies. Both are fine. What is not fine is choosing a pitch without asking where the discharge goes.
On a pole barn carport the answer is usually "onto whatever is parked below". Water runs off an open eave in a line, and in winter so does snow, in one slab, onto the side you open the door on unless the slope was turned the other way. Orient the fall away from the approach and the house wall. Gutters earn their place for the same reason, and they need somewhere to put the water.
What a Pole Barn Carport Costs

A metal post-frame kit's price per square foot falls as the footprint grows, and the table below prices each size on its own floor area. A pole barn carport is the least of what any of those ranges describe — no wall sheeting, no doors, no openers — so it sits toward the bottom of its range rather than the top.
| Size | Floor Area | Kit Price Range |
|---|---|---|
| 12×24 | 288 sq ft | $3,700–$7,200 |
| 20×24 | 480 sq ft | $6,200–$12,000 |
| 24×36 | 864 sq ft | $7,800–$27,600 |
| 30×40 | 1,200 sq ft | $10,800–$38,400 |
| 40×60 | 2,400 sq ft | $16,800–$57,600 |
Take the 24×36 as the worked example: two vehicles side by side with a bay left over for a mower, a boat or a bench. The kit is one line of the bill; the rest is the pad, putting it up, the site work and the permit.
| Line Item | Rate | Low | High |
|---|---|---|---|
| Kit | $9–$32 per sq ft × 864 | $7,800 | $27,600 |
| Concrete slab | $6–$12 per sq ft × 864 | $5,200 | $10,400 |
| Erection | $5–$12 per sq ft × 864 | $4,300 | $10,400 |
| Site preparation | sheet | $1,300 | $5,600 |
| Permits | sheet | $500 | $3,100 |
| Installed total | $19,100 | $57,100 |
That is $22 to $66 per square foot of footprint, and the spread is mostly site work rather than steel. Park on gravel and the $5,200–$10,400 slab line comes off: $13,900–$46,700. At this footprint the kit alone runs $7,800 to $27,600 — one footprint, a different building under it.
Two things move a pole barn carport's price more than width does. Height is one: every extra foot of clear height is more column, more bracing and more uplift to resist. Site preparation is the other and the widest line — a flat pad beside an existing drive sits at the bottom of the $1,300–$5,600 range, a sloped one needing fill at the top.
The pad is a real decision, not a formality
No slab is needed to stand it up: the columns are carried by their own footings or by embedment, and gravel between them drains and costs a fraction of concrete. Pour a slab when you intend to work under the roof — jack stands, a creeper, a bench. Piers are the middle route: concrete where the columns land, gravel between.
Compare Real Quotes, Not Catalogue Prices
Give the footprint, the clear height and the county once. Suppliers who price open metal post-frame buildings come back with numbers you can put side by side.
Get Free QuotesFree to compare. No obligation.
Attaching a Pole Barn Carport to a House or Shop

Running the roof off an existing wall saves a line of columns and puts the shelter where the door already is. It also creates the connection that fails first. The Department of Energy's Building America guidance on porches and carports is direct about it. "Strong winds can separate the roof structure of attached porches and carports from the supporting structure", it says, and the connections between roof members, beams, posts and foundation "are commonly the weakest link within a load path".
The remedy is the same guidance's own. "Attached porches and carports must be constructed with a strong and continuous load path from the roof to the foundation to avoid structural damage during high winds", it says. "Metal straps or connectors, fastened to the members of the attached structure and to the main house, transfer the load from the roof to the foundation." A ledger screwed to siding is not that load path.
Three practical decisions sit inside an attached pole barn carport. Where the new roof meets the old, because that junction has to be flashed and has to shed water rather than pond at it. What it does to the old roof's drainage, since one plane now feeds another. And whether the existing wall was built to take a horizontal pull — a question for whoever engineers it, not for the crew on the day.
A free-standing pole barn carport avoids all three and costs one more line of columns. It is easier to move, easier to permit in some places, and impossible to blame for a leak in the house. Attached wins when the walk from the vehicle to the door in the rain is the point of it.
Permits, Setbacks and the Height Cap

Assume a permit, and settle zoning before the structural question. The International Code Council says as much: "As a model code, the IBC is intended to be adopted in accordance with the laws and procedures of a governmental jurisdiction". It adds that "some jurisdictions amend the code in the process to reflect local practices and laws". The version enforced in your town is the one that counts.
Local wording can also decide what your building is called. One Ohio city's zoning summary states that "A carport must be permanently open on at least 2 sides, no taller than 14 feet, and be physically attached to the building". Accessory buildings there "shall not exceed 1-1/2 stories or 14 feet in height". Under that wording a free-standing pole barn carport is not a carport in the zoning sense — it is an accessory building, with its own height limit.
Setbacks are the other local rule, and an open roof is often long. Maricopa County's zoning directive allows detached accessory structures in a required yard, but they "shall not occupy more than 30% of any required yard and shall not be nearer than three feet to any side or rear lot line". Draw the footprint on the plot plan before ordering.
Four questions at the planning counter: what height is allowed for a detached accessory structure here, what setback applies, does an open roof count toward lot coverage, and what does this jurisdiction call a carport. Ask a homeowners' association the same four in writing.
When to Close the Sides In

A pole barn carport solves one problem completely and others only partly. It takes the sun, the rain and the hail off the top of whatever is under it, where damage is worst and paint repairs are dearest. It does nothing about the sides.
Buy walls and doors if any of this describes you. Wind-driven rain and blowing snow reach the flanks of a vehicle under any open roof. Low winter sun comes under the eave onto the same side all afternoon. Nothing is locked, so tools and gear have no home. And working on a vehicle in January under an open roof is an experience people need only once.
The middle route is often the best value here: sheet one end or one side. It puts a wall against the prevailing weather for a fraction of closing the whole thing in, gives you somewhere to hang a bench, and moves the building into the code's partially enclosed class. Ask for it before the drawings are sealed rather than adding it later.

Questions, Answered
At 24×36, or 864 square feet, a metal post-frame kit is $7,800–$27,600. Installed — kit, slab, erection, site work and permits — it is $19,100–$57,100, or $22 to $66 per square foot. Leave the pad as gravel and the $5,200–$10,400 slab line comes off: $13,900–$46,700.
That is an engineering decision on the sealed drawings, not a catalogue number: bay spacing depends on the span, the loads and the members. What you can pin down is the result — ask every supplier for the clear distance between columns and the clear height under the lowest member, in writing.
Deep enough for the soil and the load, and below the frost line. The code covers columns "embedded in earth or in concrete footings in earth", and takes the depth needed to resist lateral loads from its own design criteria. Foundations "shall be protected from frost" by "Extending below the frost line of the locality", and your building department holds the local figure.
Yes to the first, and plan on the second. The code gives an open building its own class — "each wall at least 80 percent open" — and requires wind loads determined in accordance with ASCE 7, with the structure "anchored to resist wind-induced overturning, uplift and sliding". Model codes are adopted and amended jurisdiction by jurisdiction.
No, it is higher. The code's thermal factor is 1.0 for "All structures except as indicated below" and 1.2 for "Unheated structures", and an open roof is unheated by definition. Design snow load on a pole barn carport is a fifth greater than on a heated building of the same shape and site.
At least the minimum for the panel. Lapped, nonsoldered seam panels without sealant need "three units vertical in 12 units horizontal"; with sealant, one-half in 12; standing-seam systems, one-quarter in 12. Above that floor, steeper sheds rain and snow sooner — and decide which side the discharge lands on before the frame goes up.
Not to hold it up. The columns are carried by their own footings or by embedment, and gravel between them drains well. A slab is for working under the roof, not for standing it up. A slab runs $6–$12 per square foot: $5,200–$10,400 at 864 square feet.
Some do, and it is worth knowing what you take on. Setting tall columns and landing roof members is height work, and the Labor Department notes that steel erection "is one of the top 10 most hazardous occupations according to BLS fatality data year after year". The erection line at this size is $4,300–$10,400.
A pole barn carport is a short list of decisions, each with one expensive mistake available. They are the clear width between columns, the clear height under the lowest member, what holds the posts down, and which way the water and snow come off. Get those four right and the rest is the predictable part, at $19,100–$57,100 installed at 24×36, or less on gravel.
So take them in that order. Measure the widest and tallest thing that will live under it. Get the design wind speed, ground snow load and frost depth for the address. Settle height and setbacks with the planning counter. Then ask suppliers for clear dimensions, the anchoring detail and the panel slope, and the quotes will compare.
Related Resources
- RV Carport
- Metal Carport
- Wood Carport
- Custom Carports
- Pole Barn Garage
- Pole Barn Cost Estimator
- 3D Pole Barn Designer
Get Quotes for Your Pole Barn Carport
Tell us the footprint, the clear height and the county. Suppliers who build open metal post-frame buildings come back with real numbers, and comparing them costs nothing.
Get Free QuotesUp to 5 quotes. No obligation.
